Concept explainers
Acetone must be kept in a closed pressure tank due to evaporation. Acetone evaporates at a rate of 3 grams per minute >[g/min]. If the tank holds 50 pound-mass [Ibm] of acetone and is allowed to remain open to the atmosphere, how many days [d] will it take for half of the acetone to evaporate?
Want to see the full answer?
Check out a sample textbook solutionChapter 7 Solutions
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Additional Engineering Textbook Solutions
Engineering Mechanics: Dynamics (14th Edition)
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Engineering Mechanics: Statics & Dynamics (14th Edition)
Statics and Mechanics of Materials (5th Edition)
- On average, a bolt of lightning provides 500 megajoules [MJ][MJ] of energy. Doctor Emmitt Brown’s flux capacitor needs 1.21 gigawatts [GW][GW] of power to his DeLorean DMC-12 time machine. How long in units of seconds [s][s] must the lightning bolt be in contact with the car to completely charge the flux capacitor? Assume 100% of the energy from the lightning is captured by the capacitor.arrow_forwardA cylindrical pipe with a cross-sectional radius r = 1.40[cm] is plunged into a l = 2.30[m] tall open water drum that is initially completely filled with water (pwater = 1000 [kg/m3]). The pipe goes h1 = 0.35 [m] above the drum before dropping down h2 = 3.50 [m] below the base of the drum as shown. The cross-sectional radius of the top side of the pipe is R = 2.20 [cm].A. How fast is the water going out of this pipe?B. What's the liquid's pressure at the top of the pipe? Assume that the system is exposed to 1.00 [atm] of air pressure.C. What's the maximum height the pipe can go above the drum before the water stops flowing out of the pipe? For liquid flow to be continuous, the liquid’s pressure must not fall before its vapor pressure. Assume that vapor pressure, in this case, is 2.30 [kPa].arrow_forwardIn a factory, 12 gallons [gal] of a liquid need to be raised 30 feet [ft] to be loaded into a piece of equipment. During this process, the electric motor loses 700 watts [W] to heat while operating in a circuit that requires 15 amperes [A] of current and 110 volts [V]. The liquid has a total mass of 5 slugs [slugs] and the mass of the container is negligible. Determine the time required to lift the liquid in seconds [s].arrow_forward
- Assume you purchase a new heat pump rated at 3 Refrigeration Tons [RT] and you estimate to use the heat pump for 13 hours per day [h/d] during the month of April (30 days), at a cost of $0.11 per kilowatt-hour [$/(kW h)]. What is the total cost, in dollars [$], to operate the heat pump in the month of April?arrow_forwardA plastic bin with a volume of 1 gallon [gal] has a mass of 0.35 kilograms [kg] when empty and is sitting on a table in a warehouse. After the bin becomes partially filled, 1.3 pounds-force [lb] of force is applied to move the bin across the table, and the bin and its contents accelerate at a rate of 1.5 meters per second squared Ignore frictional losses. Determine the total weight of the bin and its contents in units of newtons [N].arrow_forwardA robotic rover on Mars finds a spherical rock with a diameter of 8 centimeters [cm]. The rover picks up the rock and lifts it 25 centimeters [cm] straight up. The rock has a specific gravity of 4.75. The gravitational acceleration on Mars is 3.7 meters per second squared [m/s²]. If the robot's lifting arm has an efficiency of 35% and required 10 seconds [s] to raise the rock 25 centimeters [cm], how much power in units of watts [W] did the arm use?arrow_forward
- A 4.5-centimeter [cm] radius cylindrical tank holds a liquefied version of a new polymeric compound for space flight to Mars. The tank is pressurized to prevent evaporation at a surface pressure of 1.38 bar [bar]. A total pressure probe located at the bottom of the tank reads 21.45 pound-force per square inch [psi]. If the specific gravity of the gel is 8.9, what is the mass of gel contained in the tank in units of kilograms [kg]? Assume acceleration due to gravity simulated on the spacecraft to be 8.4 meters per second squared [m/s]. Click the icon to view the conversion table. The mass of the gel is .02 kg. (Round your answer to two decimal places.)arrow_forwardTo heat potatoes, you use a microwave with an output power of 780 watts [W]. The microwave has "pre-set" cook buttons. The "potato" button will cook a 0.625 pound-mass [lbm] potato by heating the potato from room temperature (assumed to be 68 degrees Fahrenheit [°F]) to 425 degrees Fahrenheit [°F]. The specific heat of a potato is 3.4 kilojoules per kilogram kelvin [kJ/(kg K)]. What is the length of time the "pre-set" button is programmed to operate in units of minutes [min]?arrow_forwardA 4.5-centimeter [cm] radius cylindrical tank holds a liquefied version of a new polymeric compound for space flight to Mars. The tank is pressurized to prevent evaporation at a surface pressure of 1.38 bar [bar]. A total pressure probe located at the bottom of the tank reads 21.65 pound-force per square inch [psi]. If the specific gravity of the gel is 8.9, what is the mass of gel contained in the tank in units of kilograms [kg]? Assume acceleration due to gravity simulated on the spacecraft to be 8.4 meters per second squared [m/s2].arrow_forward
- The following processes occurs in a reversible thermodynamic cycle: 1-2: Reversible polytropic compression at pressure [X] bar at volume [Y] m3 to a pressure [Z] bar and specific volume [A] m3/kg. The index of compression may be taken as n. 2-3: Reversibly expansion with expansion index of 2 to pressure [B] bar. 3-1: Reversible cooling at constant volume to the initial state. What are the final attempt values of X, Y, Z, A and B from the Part A of the eThuto Assessment. calculated formula similar question? X= ; Y= ; Z= ; A= ; B=arrow_forwardWater enters a boiler at 20 degrees Celsius [°C]. The boiler operates for 5 minutes [min] to heat 25 gallons [gal] of water. The boiler requires an input power of 15.5 kilowatts [kW] and is 85% efficient. The specific heat capacity of water is 4.18 kilojoules per kilogram kelvin [kJ /(kg K)]. What is the temperature of the water in degrees Celsius [°C] as it exits the boiler?arrow_forwardYou have 4 springs, one each 3.5, 6, 8.5, 11 newtons per meter. How close an equivalent stiffness to the average of the four springs (7.25 newtons per meter [N/m]) can you make using only these springs? You may use all four springs to do this, but you may use less if that will yield an equivalent stiffness closer to the average.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY