The rate of heat flow (conduction) between two points on a cylinder heated at one end is given by dQ-A dt dT dx where λ is a constant, A is the cylinder's cross-sectional area, Q is heat flow, I'is temperature, t is time and r is the distance from the heated end. Given that where L is the length of the rod. dT 100(L-x)(20-1) dx 100-xt If the initial condition is Q(0)= 0 and the parameters A is the last digits of your matrix number, L = 24, x=2.5 cm and 2 = 0.4 cal cm/s. For example, student with matrix number DD190010 will have the values of A = 0 and L = 20. Calculate the heat flow for t=0 to 35 s using Heun's method. Use h = 5.

The rate of heat flow (conduction) between two points on a cylinder heated at one end is given by dQ-A dt dT dx where λ is a constant, A is the cylinder's cross-sectional area, Q is heat flow, I'is temperature, t is time and r is the distance from the heated end. Given that where L is the length of the rod. dT 100(L-x)(20-1) dx 100-xt If the initial condition is Q(0)= 0 and the parameters A is the last digits of your matrix number, L = 24, x=2.5 cm and 2 = 0.4 cal cm/s. For example, student with matrix number DD190010 will have the values of A = 0 and L = 20. Calculate the heat flow for t=0 to 35 s using Heun's method. Use h = 5.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.22P: 1.22 In order to prevent frostbite to skiers on chair lifts, the weather report at most ski areas...

See similar textbooks

Similar questions

= 1000N 1000N
R(A)sin30 R(B)sin45 R(A) 400lb R(B) DN 45 R(B)cos45' 43 30 A 60 R(A)cos30 B Determine the value of Rb #
3. Thermal conductivity of a substance is measured as k = k, TIT, . Find an average value for thermal conductivity in the temperature range of T1 and T2. [Ans. = (k, /272 xT} 2 – T}/2) (T2 – T;) 1|
B 45 20 R20 20 IS 70 90
Material 1- BRASS The below shown graph is drawn from the tabulated values of steel which we measured during the experiment of thermal (Diameter = 25mm) conductivity: (Consider the value of heater power (Q') and the area of cross section (A) of the material from the tabulated values) Power X-axis 1 unit =1 cm y-axis 1 unit = 10°C Temperature (°C) 50- Q' 1 2 3 4 5 6 7 8 (W) 14.65 79 77.4 76 50.1 46.5 42.4 36 34.5 : 20- 10- Distance X in cm 123 10 Material 2 - STEEL Calculate the following: Thermal conductivity of (Diameter = 25mm) steel Calculated Value quantities Power Difference in temperature (AT) C° (with sign) Difference in distance Temperature (°C) between test points (Ax) cm Slope from the graph °C/m (with sign) Q' 1 (W) 2 3 7 8 Thermal conductivity of steel ksb W/m°C 14.2 88.6 87.5 85 33.9 33.6 32.4
Which of the following is the unit for electrical conductivity? Select one: O (Q-m) -1 O (Q-mm) O m/S O Q-m In a stress strain curve of mild steel, the elastic limit will be before the limit of propor ype here to search 99+ hp fs 米 f5 f6 f7 1- f8 fg & 7 V 3 6. 8. 9/6 4+ %24 %23
The population of a community is known to increase at a rate proportional to the number of people present at time t. If an initial population P, has doubled in 7 years, how long will it take to triple? (Round your answer to one decimal place.) yr How long will it take to quadruple? (Round your answer to one decimal place.) yr еВook
1.71 The thermal conductivity of silver at 212°F is 238 Btu/h ft °F. What is the conductivity in SI units?
1.22 In order to prevent frostbite to skiers on chair lifts, the weather report at most ski areas gives both an air temperature and the wind-chill temperature. The air temperature is measured with a thermometer that is not affected by the wind. However, the rate of heat loss from the skier increases with wind velocity, and the wind-chill temperature is the temperature that would result in the same rate of heat loss in still air as occurs at the measured air temperature with the existing wind. Suppose that the inner temperature of a 3-mm-thick layer of skin with a thermal conductivity of 0.35 W/m K is and the air temperature is . Under calm ambient conditions the heat transfer coefficient at the outer skin surface is about (see Table 1.4), but in a 40-mph wind it increases to . (a) If frostbite occurs when the skin temperature drops to about , do you advise the skier to wear a face mask? (b) What is the skin temperature drop due to the wind?
x-axis 1 unit = 1cm y-axis 1 unit = 5 °C 90 80 70 60 50 40 30 20 10 x ст 1 2 3 4 7 8. 9. 10 Distance of the test point from the hot end in centimeter Temperature in degree celsius
1. The wheel starts rotating from rest, 2) if its angular velocity Was a function of angular position 0 is W=0.1-0², where O is in radian, and its radius ris 0.2 m, what is the magnitude of the angular acceleration (in rad/s?) of the wheel after the wheel has turned 1.1 revolution(s) from rest. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. P
Each time your heart beats, your blood pres- sure first increases and then decreases as the heart rests between beats. The maximum and minimum blood pressures are called the systolic and diastolic pressures, respectively. Your blood pressure reading is written as systolic/diastolic. A reading of 120/80 is considered normal. A certain person's blood pressure is modeled by the function p(1) = 115 + 25 sin(16071) where p(t) is the pressure in mmHg (millimeters of mer- cury), at time t measured in minutes. Find the blood pressure reading. How does this compare to normal blood pressure?