The composite bar consists of a 20-mm-diameter A-36 steel segment AB and 50-mm-diameter red brass C83400 end segments DA and CB. Determine the displacement of A with respect to B due to the applied load. (Figure 1) Express your answer to three significant figures and include the appropriate units. Figure < 1 of 1 > 250 mm- -500 mm- 250 mm- 50 mm 20 mm 75 kN 100 kN, D A 75 kN 100 kN B µA 6A/B = Value Submit Request Answer Provide Feedback Units ?

The composite bar consists of a 20-mm-diameter A-36 steel segment AB and 50-mm-diameter red brass C83400 end segments DA and CB. Determine the displacement of A with respect to B due to the applied load. (Figure 1) Express your answer to three significant figures and include the appropriate units. Figure < 1 of 1 > 250 mm- -500 mm- 250 mm- 50 mm 20 mm 75 kN 100 kN, D A 75 kN 100 kN B µA 6A/B = Value Submit Request Answer Provide Feedback Units ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel [E = 200 GPa] rod with a circular cross section is 13-m long. Determine the minimum diameter D required if the rod must transmit a tensile force of 23 kN without stretching more than 4 mm. 13.18 mm 28.25 mm 20.13 mm 25.90 mm 21.81 mm
The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The cross-sectional area of each rod is given in the figure. A force of P = 42 kip is applied to the ring F. Part A Determine the horizontal displacement of point F. Use Et = 17.4(10³) ksi. Express your answer to three significant figures and include appropriate units. SF HA Value Submit Request Answer Units ? AF = 2 in² 1 ft F 2 ft P 2 ft A E 6 ft AAB = 1 in ² Acp=1.5 in² 6 ft B D
The 24-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa. (Figure 1) Figure 600 mm B 400 mm 50 kN 50 kN C 40 kN 1 of 1 > ▾ Part A Determine the displacement of end C with respect to the fixed support at A. Express your answer to three significant figures and include the appropriate units. dc = Submit μA Value Provide Feedback Request Answer Units ? 4
In (Figure 1), F = {35i - 40j +60k} lb. Figure 401 1 of 1 > Part A Determine the magnitude of the component of F acting along segment BC of the pipe assembly. Express your answer to three significant figures and include the appropriate units. (FBC) = 25.0 Submit Previous Answers Request Answer Part B HA X Incorrect; Try Again; 5 attempts remaining lb Determine the magnitude of the component of F acting perpendicular to segment BC of the pipe assembly. (FBC)= Value Submit Express your answer to three significant figures and include the appropriate units. Provide Feedback Request Answer ? Units ? Next >>
The rigid metal strip of negligible weight is used as part of an electromagnetic switch. The stiffness of the springs at A and B is k = 9 N/m and the strip is originally horizontal when the springs are unstretched. (Figure 1) Part A Determine the smallest force F needed to close the contact gap at C. Express your answer to three significant figures and include the appropriate units. HẢ ? F = Value mN Submit Request Answer Provide Feedback Figure 50 mm 50 mm B 10 mm
When the two forces are placed on the beam, the diameter of the A-36 steel rod BC decreases from 40 mm to 39.96 mm. (Figure 1) Figure -1 m -1 m P -1 m- B 0.75 m 1 m Part A Determine the magnitude of each force P. Express your answer to three significant figures and include the appropriate units. P = μA Value KN Submit Previous Answers Request Answer Provide Feedback ? X Incorrect; Try Again; 2 attempts remaining
The results of a laboratory test that is used to assess the mechanical or failure characteristics of metals are shown below. Select labels for both of the plot axes. Х-аxis Cycles to failure Stress Y-axis Impact energy Time Strain eTe Stress amplitude Temperature
The results of a laboratory test that is used to assess the mechanical or failure characteristics of metals are shown below. Select labels for both of the plot axes. Х-аxis Stress Y-axis Impact energy Stress amplitude Strain Time eTe Cycles to failure Temperature
Determine the nodal displacement of the bar shown in Figure 1 using two element of equal length. The radius varies as r(x) = 0.050 - 0.040x:, where r and x are in meters. Assume E = 200MPA. Both ends of the bar are fixed, and F = 10,000 N is applied at the center. F 10,000N- -L= I m
Abar having a length of 5 in and cross-sectional area of 0.7 in² is subjected to an axial force of 8000 b Figure 8000 lb 5 in 1of1 > 8000 b Part A If the bar stretches 0.0010 in determine the modulus of elasticity of the material. The material has linear elastic behavior (Figure 1) E = VAE Ivec Submit Previous Answers Request Answer X Incorrect: Try Again; 4 attempts remaining Provide Feedback ? ksi
Qate Find the MOVEMENT OF INERTIA eentroidal x-axis centroidal y-axic af egiven Figuse 02- about and
The shear stress-shear strain diagram for a material is shown. The bolt used to hold the lap joint is made of this material and has a diameter of 0.35 in. The material has a Poisson's Ratio of 0.2. T (ksi) F T1 G = Values for the figure are given in the following table. Note the figure may not be to scale. Variable T1 Y1 Value 40 ksi 0.003 rad 71 -7 (rad) a. Determine the Shear Modulus of the allow, G. b. Determine the Elastic Modulus of the allow, E. c. Determine the force required to cause the material to yield, F. Round your final answers to 3 significant digits/figures. ksi