The 544g collar is free to slide on the smooth rod OA. The rod rotates about pin O at constant angular velocity, é. $2 a ==en + še, = a = RÔ?e, + RÖe, for a circular path, R = radius 2.1 Use N-T coordinates, draw a FBD and a kinetic diagram to determine the minimum value of è for which the collar will maintain contact with the stop at A throughout the rotation. 2.2 Would friction between the collar and the rod affect your result in 2.1?

The 544g collar is free to slide on the smooth rod OA. The rod rotates about pin O at constant angular velocity, é. $2 a ==en + še, = a = RÔ?e, + RÖe, for a circular path, R = radius 2.1 Use N-T coordinates, draw a FBD and a kinetic diagram to determine the minimum value of è for which the collar will maintain contact with the stop at A throughout the rotation. 2.2 Would friction between the collar and the rod affect your result in 2.1?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The spring-toggle system is in the vertical plane and is held at rest with = 45° when a moment of 12 N-m is applied at point C. In the initial position, the spring, with stiffness of 140 N/m, is stretched 150 mm. Bar AB has a mass of 3 kg, and bar BC has a mass of 6 kg. Find the angular velocity of BC at the moment when = 0. Neglect friction effects. Type here to search ThinkVision Tab Caps Lock Eve Q FI W S 3 F₂ E D 4 F3 R % 5 F4 T F G 6 Y H F$ 7 U F6 8 F7 ( 9 FB Fa F10 F11 F12 - Backspace Enter Print Screen Sya Ra Insert 250 mm Scroll LOCK 00 Delete Home End Pause Break Page Up Page Down A Num Lock 7 Home 250 mm OB 250 mm O 37°F Cloudy 2:12 PM ^4 11/16/2022 Lenovo Polp
A gear of mass m = 10 kg and radius R=0.25 m may rotate about its center of mass C, which is fixed. A rack of mass m = 10 kg is subjected to a constant force Fo = 20 N, as shown. The rack and gear are geared together (gear teeth not shown), so that the force Fo drives the rack to the right and rotates the gear. Find the angular ácceleration a of the gear and find the force f exerted by the rack on the gear. The gear is to be modeled as a uniform circular disc. Fixed Fo3 20 N Rack
PROBLEM 2 For the mechanism, shown on the figure, @nc = const=5s. O4-BC-0,3 m. AB 0,6 m. Determine: a) velocity and acceleration of the point B: b) angular acceleration of the body BC: c) angular velocity and angular acceleration of the body O4: d) linear velocity and acceleration of the point 4. 120
For the four-bar linkage in the posture shown, find the angular velocities of links 3 and 4, and the velocity of point C. When w2 = 60 rad/s ccw, RAO, = RBA = 6 in, Ro.0, = RBO, = 10 in, and RCA = 8 in. %3D y 3. 4 90°
Given: A uniform slender rod is at rest upon a frictionless horizontal surface when a force (F) is applied in the direction shown. Assume that the rod has mass m and length L. A L Horizontal Plane Given that F = 74lb, L = 7.1 ft, mg = 4.6lb, and 0 = 73deg What is the component of acceleration of the mass at point G in the i direction? Answer: Check What is the component of acceleration of the mass at point G in the j direction? Answer: Check What is the component of angular acceleration of the mass in the k direction? (remember your signs) Answer: Check
The thin rectangular block is supported at its corners by small rollers resting on smooth horizontal surfaces. If b = 0.5 m and h= = 0.3 m, calculate the magnitude of the angular acceleration of the block at the moment when the supporting surface at B is suddenly removed. Present your answer in rad/sec² using 3 significant figures. h B
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of ? = 55° shown in the figure. Find the tension forces at the strings AB and AC.
2. Consider the 5-1lb bar with length of 2½ feet and width of 2 inches. Small frictionless bearings are mounted to the ends, constraining the motion of the bar to the horizontal x and y slots. The bar starts at rest at positioned at 0= 45°. If an angular acceleration of 3 rad/s² is desired, what moment M must be applied to the bar? What are the reaction forces at A and B at that instant? Additional question: Does the width of the bar matter, or is it appropriate to consider the bar as a slender rod? Consider errors of less than 2% negligible.
4. 1) The hydraulic cylinder D extends, moves the rigid rod ABC, and causes the collar A to move with velocity and acceleration both to the left. Select the location of the instantaneous center of zero velocity (IC) for rod ABC. point F point E point B point G point D point A point C O O O D B B 0 v a v a
The below figure shows a cylinder of 13 kg mass, 0,3 m radius, undergoing unconstrained planar motion under the action of two forces F1=181 N and F2=76 N as shown. Calculate the angular acceleration of the cylinder in rad/s2. (Hint: I=½mr2) (If the direction of the angular acceleration is CCW, just enter the value of it without any sign. If it has CW direction, enter "-" sign "negative sign" before the value such as "- 12,12". Allowable tolerance for this question is relatively 2 percent.) F2 Fi
In his mission as a spy, Loid Forger fired a bullet weighing mB = 0.007 kg with a horizontal speed of VB= 550 m/s into the lower end of a gate which can be modeled into a slender m=16-kg bar of length L=1.5m for simplified analysis only. Know that h=0.25 m and that the gate, which has a pin connection at point C, is initially at rest. The bullet becomes embedded into the gate after impact. 1.5 m с A D 0.25 m VB= 550 m/s
2 Problem The mechanized arm shown below is simulatenously rotating upward and extending as it holds a circular widget of mass 2 kg in its claw. At the instant shown, 0 = 45 deg., 0 = 30 deg/s. * = 120 deg/s², and L = 0.4m, L = 0.5 m/s, and Ï = -0.3 m/s². The constant length d = 1 m. Determine the components of the gripper's force exerted on the widget. Express the total force in components of the polar frame. Compare your answer with the total force on the widget if the mechanized arm suddenly stops and remains at rest. 0 L ----- B