QUESTION 4Q4.1 Show how can a series RLC can be used as a crude band-reject filter?Q4.2 How would you determine the centre frequency for this filter?Q4.3 Show how a graph of H(jo) versus oo for this filter will look like.Q4.4 In the graph, show the possible locations of the centre frequency, and the two cutoff frequencies.Justify why you chose these locations in the graph.

Band reject filter:-If the overall position of the interference in the frequency plane has been…

QUESTION 4 Q4.1 Show how can a series RLC can be used as a crude band-reject filter? Q4.2 How would you determine the centre frequency for this filter? Q4.3 Show how a graph of H(jo) versus @ for this filter will look like. Q4.4 In the graph, show the possible locations of the centre frequency, and the two cutoff frequencies. Justify why you chose these locations in the graph.

QUESTION 4 Q4.1 Show how can a series RLC can be used as a crude band-reject filter? Q4.2 How would you determine the centre frequency for this filter? Q4.3 Show how a graph of H(jo) versus @ for this filter will look like. Q4.4 In the graph, show the possible locations of the centre frequency, and the two cutoff frequencies. Justify why you chose these locations in the graph.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the filter: a) Determine type of filter and the cut-off frequency (Fc). Determine the peak voltage at the cut-off frequency (Fc). b) Find GAIN (Vo/Vi) at f = .1*Fc . Find GAIN (Vo/Vi) at f = 10*Fc . c) Determine the frequency at which GAIN = .4 (i.e., Vo = .4*Vi) . Draw the “Frequency Response Plot” in “Log-Log” format .
Design an ACTIVE band-pass filter for the midrange part of a loudspeaker so that the bandpass region is 400 Hz-2000 Hz (as defined by the -3dB points). Design the circuit so that the absolute gain is 2. a. Draw the circuit diagram and specify the resistor and capacitor values. Assume you can use either 100, 330, 500, or 1000 Ohm resistors and can select any value of capacitor. b. Sketch the frequency response (Gain [dB] vs. frequency (Hz)). Note that you will need to convert your gain to dB before plotting. Magnitude (dB) 15 10 5 midrange 12 1 -5 -10 -15 -20 -25 10 100 1,000 Frequency (Hz) 10,000 100,000
What is the transfer function of a filter? Describe how the transfer function of a filter can be determined using laboratory methods.
What is a bandpass filter? How is its bandwidth defined?
1. Choose which basic filter response suit the signal output criteria in the figure 2. State your reason. 2. Sketch the basic filter response to suit the output citeria in Figure 2. (with labelling of passband, transition region and cut-off frequency). 3. Choose 1 type of filter if a flat pass-band gain response is required.
5. Why we use semiology paper to draw the frequency response of filters. 6. What is filter order, and what is the effect of changing filter order on the filter response and complexity of filter. 7 Sketch the frequency response of low-pass, band-pass, high-pass, and band-reject filters.
2. a) Consider the circuit shown in figure 3. i) Determine what type of filter is shown in Figure 3 i) Calculate the corner or cutoff frequency. Take R = 4 k &, L= 2 H, and C= 1 uF. R Figure 3 b) Describe the possibility of building a second order filter with only resistors and capacitors? and design the cutoff frequency of second order filter for low pass filter (Expected: Describe the possibility , design the second order filter for low pass filter circuit and design the cutoff frequency as equation only).
Discuss the effect of increasing the order of the filter on the frequency response of the filter.
what is the main differences between ideal filters and real filters.
filter specification a. What kind of filter is this? b. What is the transition band of the filter is given as ₂ = 0.4, , = 0.5, ₁ = 0.01, &₂ = 0.00001, c. Draw the absolute specification d. What is the specification in relative? e. Draw the relative specification. f. If the filter is applied on a signal sampled at 100 kHz, what are the frequency edges in Hz?
a)Draw a general graph showing its gain verses frequency with gain in dB vs log of frequency and indicate the cut-off Frequency. b) Draw a simple, single resistor, single capacitor high pass filter. What is the formula for the cut-off frequency for this filter? c) Draw a graph of its gain verses frequency and label its cut-off frequency.
What is a criteria to find low pass filters, bandpass filter and highpass filter from a pole zero plot?