For the model pump below (impeller size: 37.1 cm; shaft speed: 2133.5 rpm), if it is operated to achieve a pump efficiency of 60% at a discharge within the range between 0 and 0.25 m³/s, using a shaft speed of 1800 rpm instead, what will most approximately be the power coefficient? Assume water density 1000 kg/m³.

For the model pump below (impeller size: 37.1 cm; shaft speed: 2133.5 rpm), if it is operated to achieve a pump efficiency of 60% at a discharge within the range between 0 and 0.25 m³/s, using a shaft speed of 1800 rpm instead, what will most approximately be the power coefficient? Assume water density 1000 kg/m³.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

P (6-5) Two centrifugal pumps are connected in parallel in a given pumping system. Plot total head Ah against capacity Q pump and system curves for both pumps running on the basis of the following data: Operating data for pump 1 Operating data for pump 2 Ahm, 40.0 35.0 30.0 25.0 Ah m. 0.0 35 30 25 Qim³/h. 169 209 239 265 Q₂m/h 0 136 203 267 data for system Ah m, 20.0 25.0 30.0 35.0 Q.m³/h, 0 244 372 470
1(C) A centrifugal pump has an impeller of diameter (D) of 300mm. When pumping 20°C water at a fixed rotational speed of 1500 RPM, the measured flow rate Q and pressure rise Pare given by the manufacturer as follows: Flow Rate (L/s) 13 19 25 32 38 44 Pressure Rise (Bar) 2.5 2.4 2.35 2.2 2.0 1.6 It is desired to use the same pump, running at 945 RPM, to pump 20°C water at 22L/s. According to your dimensionless correlation, what pressure rise p is expected?
Data measured during tests of centrifugal pump driven at 3000 rpm are Parameter Inlet, Section 1 Outlet, Section 2 Gage pressure, p (kPa) 90 Elevation above datum, z (m) 10 Average speed offlow,V (m/s) The flow rate is 15 m3 /hr and the torque applied to the pump shaft is 6.5 N.m. The pump efficiency is 75%, and the electric motor efficiency is 85%. Find the electric power required, and the gage pressure at outlet, section 2. Write the pump specific speed in terms of the flow coefficient and the head coefficient.
Example 1: A system has a volume flow rate requirement of 1lit/s with an index run AP of 30kPa. Find an appropriate pump from the A manufacturer's catalogue gives the following information for a centrifugal pump operating at 12rev/s: P| 49.38 47.5| 44.38 40 34.38 27.5 19.38 Q|0.25 0.5 0.75 1.25 1.5 1.75 yelume flow rate
Example (6-1): At the best efficiency point a centrifugal pump, with impeller diameter D=8 in, produces H= 21.9 ft at Q=300 gpm with N=1170 rpm. Compute the corresponding specific speed using a) U.S. customary units. B) SI units (rad/sec, m/sec, m'/sec").c) European units (rev/sec, m/sec, m/sec?). Develop conversion factors to relate the specific speeds.
Figure below shows the performance curve family of Model 5009 Centrifugal pumps of Taco Pump Inc., running at a fixed speed of N = 1160 rpm. For the pump with the impeller diameter D = 8.625 in., you are asked to determine the best efficiency point (BEP) of the given pump. What is the pump efficiency at BEP? HEAD IN FEET 50 0 0 0 0 40 20 10 O 81% 8.625" 30 (219mm). O 51% O 71% ○ 61% O Taco L/SEC 5 9.25" (235mm) 8.00" (203mm) 7.375" (187mm) 6.75" (171mm) 0 10 15 125 Model 5009 FI & CI Series 20 25 CURVES BASED ON CLEAR WATER WITH SPECIFIC GRAVITY OF 1.0 8 8 52 75% 77% 30 79% 1160 RPM FEBRUARY 19. 2002 35 40 45 REQUIRED NPSH olº 1.5HP (1.1KW) dot 17% Curve no. 2140 Min. Imp. Dia. 6.75" Size 6 x 5 x 9.0 50 55 60 75% 72% 250 375 500 625 FLOW IN GALLONS PER MINUTE 8% 2HP(1.5KW) 750 %09. 55% (2.2KW) 3HP 7.5HP(5.6KW) 2015 do 35% 875 FEET 15 12 -9 6 SHP(3.7KW) 3 0 10 8 NPSH 1000 HEAD IN METERS 5 KPo 45 -36 27 18 9 -0 100 -80 60 -40 2 -20 8 HEAD IN KILOPASCALS
EX1: Given are the following data for a commercial centrifugal water pump: r1 =10 cm, rz = 17.5 em, B1 =30°, B2 =20°, speed =1440 r/min. Estimate (a) the design point discharge, (b) the water horsepower, and (c) the head if bs = bz = 4.4 cm.(Hint. design point discharge, i.e €:=90°)
Problem-4: The characteristics for a pump are given in the table below. The pump is required to left water against static head Az = EN" m. The pipe arrangement has a total length L the pump discharge, head, efficiency and power for the given pipe system. 200, d = 0.1 m and f= 0.016. Find %3D Q (L/s) 10 20 30 35 42 50 Hp (m) efficiency % 210 201 180 150 129 93 48 30 58 80 85 86 74 EN=62 Hp = Az + h, = Az + 12.1 d P = 757
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) the pump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
This course EHide block A centrifugal pump with the following impeller dimensions is used to pump water. The pump is running at 1000 rpm. The ideal head rise through the pump is 190 ft. b2 Poz 72 by The parameters of the impeller are as follows: r2= 9in, b2=3in, B2= 31° Take g= 9.81 m/s23 32.2 ft/s2 pw = 998 kg/m3 = 1.94 Slug/ft. Determine the theoretical flow rate in gpm Choose.. Determine the theoretical Power shaft in (hP) Choose...
A prototype pump is designed to so that the attached dimensionless performance curves apply. (a) If the pump is powered by a fixed speed motor delivering a rotational speed of 400 rpm and the impeller diameter is 2 m find the unknown quantities (Q, H, P,n ). Assume the pump is operating a peak efficiency and is pumping cold water. (b) If the pump is to be connected to standard steel pipe, which pipe should be used. Сн 1.00 Efficiency-n 0.75 CH 3 0.50 0.25 0.04 0.08 0.12 0.16 Ce C, and Efficiency
The performance data for a centrifugal water pump are shown in Table for water at 77°F (gpm = gallons per minute). (a) For each row of data, calculate the pump efficiency (percent). Show all units and unit conversions for full credit. (b) Estimate the volume flow rate (gpm) and net head (ft) at the BEP of the pump