For the bracket and loading condition shown above, determine the smallest size Grade 8.8 metric bolt needed to hold the bracket in place that will still provide a minimum factor of safety of 2 versus the proof strength of the bolt. Assume coarse threads. Neglect the vertical shear on the bolts. All dimensions are in millimeters.

For the bracket and loading condition shown above, determine the smallest size Grade 8.8 metric bolt needed to hold the bracket in place that will still provide a minimum factor of safety of 2 versus the proof strength of the bolt. Assume coarse threads. Neglect the vertical shear on the bolts. All dimensions are in millimeters.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook. Condition #2: The same structural support of the basic size determined in Condition 1 is subjected to a tensile load of 15 kN that is repeated several thousand times over the life of the machine. This load is not an addition to the 20 kN. Specify a suitable steel that is suitable to this application based on the basic size determined in Condition #1. Loading of Condition #1 does not apply here. Condition #3: The same structural support from Condition 2 is heated from room temperature of 25°C. The support is placed inside a frame on both ends. There is a total clearance of 0.2 mm between the support and its frame. Initial length of the rod is 200 mm. Specify the…
3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.
Q1:Prepare a full-section assembly drawing of the four fastener assemblies shown in the Figure. Dimension both the clearance and the threaded holes. A top view may be shown if required. Scale 1: 1. .250-20 FHMS .375 HEX BOLT AND NUT THREADED INTO BASE 1.00 ↓ .50 T 2.00 Ø.375 STUD THREADED .312 HEX X 1.25 LG INTO BASE FOR 1.00 IN. CAP SCREW AND WITH HEX NUT AND LOCK WASHER ON SPOTFACE SURFACE PLATE WASHER A 2.00- -2.00 -1.00- BASE 1.00- .25 1.50
1- A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic motor runs at 1200 r.p.m to the driven shaft which runs at 350 r.p.m. The drive is required to operate continuously with drop lubrication and driven machine is such that load can be regarded as fairly constant. Design the chain drive by calculating leading dimensions, number of teeth on the sprockets taking into account that the available distance between the two shafts centers is 400mm + 4% no more no less.
The allowable tensile stress for a ½ bolt of thread length 7/32 inches is 30000 psi. The allowable shear stress of the material is 15000 psi. Where and how such a bolt most likely to fail, will it fail in the root diameter or the in the thread.
Q2/ A 3/4in-16 UNF SAE grade 5 bolt is subjected to a load of 8 kip in a tension joint. The initial bolt tension is F 30 kip. The bolt and joint stiffness's are kb=8 & km=15Mlbf/in, respectively. a) Determine the preload and service load stresses in the bolt. Compare the to the SAE minimum proof strength of the bolt. b) Specify the torque necessary to develop the preload.
1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
The head of a 300 mm diameter cylinder vessel will be designed. The internal pressure in the cylinder is Pin = 1MPA. The bolts have initial tightening load of 12 kN. a) Find the stiffness of the bolt and members. b) Determine the number of bolts (N) for a safety factor of 2 for fatique loading. IMPA D= 300 mm M 10 1.5 grade 5.8 cast iron E= 200 GPa Eci= 90 GPa
Determine the torsion on the rigid supports and the maximum shearing stress developed in each segment. Provide a torque diagram, strictlv follow instructed sign convention, and start from left to right. Use 2 decimal places. A 0.5 in. B 5 in. C 500 lb-ft 8 in. 1 in. D 12 in.
find the tensile of the bolt with diameter 38mm,80kN
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (Sf) is equal to 0.8 Su and endurance Strength (Se) is equal to 0,5 Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S-N diagram
Q1 A single-square thread power screw is to raise a load of 100KN. The screw has a major diameter of 42 mm and a pitch of 6 mm. The nut for the screw transfers the load as shown in the F/2 F/2 figure right. The power screw is made of carbon steel having Sy=350MPA and Sut= 500MPa. The nut is to be made of ASTM 25 gray cast iron having S,=220MPA and Suc=670MPA. The friction on the screw threads is 0.15 and the friction on the nut is ignored. Calculate; i) ii) iii) iv) Raising and lowering torques Efficiency for raising the load Check for the self-locking condition Nut height (h) when considering the failures due to direct shear at the root of the thread and bearing stress failure on nut. Take the factor of safety as 3. Critical load when the power screw is at maximum height of 850mm. v)