CDEFGH is plate with a circular hole in it and has a unit weight p (N/m?). It is attached on DEbeam with weld. A crate has a weight of W (kN) at A is linked to the plate from C by the helpof a cord. The surface under the crate has a coefficient of static friction u1 and the pulley has acoeficient of static friction µ2.a) Find the center of the gravity of the CDEFGH plate according to O (given in grey color inthe figure).HCD is half circle centered at O.A full circle centered at O is removed from the plate.• HOD line and EF line are vertical.ВAHG3mCed.FImDEK2maа (m)b (m) c (m) d (m)p (N/m²)3251300.20.2200

Center of gravity: The point in a system where the total weight or mass of the body is assumed to be…

CDEFGH is plate with a circular hole in it and has a unit weight p (N/m²). It is attached on DE beam with weld. A crate has a weight of W (kN) at A is linked to the plate from C by the help of a cord. The surface under the crate has a coefficient of static friction u1 and the pulley has a coeficient of static friction uz2- a) Find the center of the gravity of the CDEFGH plate according to O (given in grey color in the figure). • HCD is half circle centered at O. • A full circle centered at O is removed from the plate. HOD line and EF line are vertical. B A н G Hi 3m d. F Im D E K 2m a b a (m) | b (m) c (m) d (m) p (N/m²) 3 2 5 1 30 0.2 0.2 200

CDEFGH is plate with a circular hole in it and has a unit weight p (N/m²). It is attached on DE beam with weld. A crate has a weight of W (kN) at A is linked to the plate from C by the help of a cord. The surface under the crate has a coefficient of static friction u1 and the pulley has a coeficient of static friction uz2- a) Find the center of the gravity of the CDEFGH plate according to O (given in grey color in the figure). • HCD is half circle centered at O. • A full circle centered at O is removed from the plate. HOD line and EF line are vertical. B A н G Hi 3m d. F Im D E K 2m a b a (m) | b (m) c (m) d (m) p (N/m²) 3 2 5 1 30 0.2 0.2 200

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.5.2P

See similar textbooks

Similar questions

The papped cantilerer beam Andye Draw SFD Bno and Eleshc casre. Consiskent defomution methed. EI b constant bm
Dr. A H.W.5: A rigid bar ABCD is supported by two bars, as shown in Fig- ure 3 .There is no strain in the vertical bars before load Pis applied. After load P is applied, the normal strain in rod (1) is -570 pm/m. Determine (b) the normal strain in rod (2) if there is a l-mm gap in the connection at pin C before the load is applied. (c) the normal strain in rod (2) if there is a l-mm gap in the connection at pin B before the load is applied. (a) the normal strain in rod (2). (2) 1,500 mm 360 mm 140 mm 240 mm Rigid bar bber C B 900 mm (1)
Q1: The steel strap with thickness of 12 mm is to be welded to a rig id frame to carry a static load of F=20 kN. The strap and frame are we lded together by fillet welds along two sides. Using the max imum distortion energy theory, determine the minimum length of the we ld to be on safe side. The yield strength is 420 MPa. The safety factor should be considered as 4. (k=12 mm)
12-2. The L2 steel blade of the band saw wraps around the pulley having a radius of 12 in. Determine the maximum normal stress in the blade. The blade has a width of 0.75 in. and a thickness of 0.0625 in. Prob. 12-2 12 in.
Q.1/The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is applied. The connection at A is a pin, and AB is supported on the steel rod BE and the copper rod CF. The length of BE & CF is 250 mm. The cross sectional area of CF is 400 mm, the area of BE is 200 mm. Determine the stress in each of the vertical rods . The weights of all bars are negligible. For copper E=120 GPa, for steel E=200 GPa. 200 KN 1.5 m 500 mm 1500 mm 250 mm steel copper
If the required clamping force at the board A is to be 2 kN, determine the torque M that must be applied to the screw to tighten it down. The square-threaded screw has a mean radius of 10 mm and a lead of 3 mm, and the coefficient of static friction is μs = 0.35.
A 14 mm diameter steel (E - 213 GPa) rod (2) is connected to a 23-mm wide by 11-mm thick rectangular aluminum (E - 60 GPa) bar (1), as shown. Assume l-0.7m and L-142 m. Determine the force Prequired to stretch the assembly 6.9 mm. (1) (2) kN.
Determine the principal stresses. Show all results on complete sketches of differential elements. (input the Maximum Principal Stress in the answer box) ox- 65 ksi, ay - 89 ksi, Dxy - 58 ksi
The bronze C86100 pipe has an outer diameter of 1.5 in. and a thickness of 0.125 in. The coupling on it at C is being tightened using a wrench. If the torque developed at A is 125 lb # in., determine the magnitude F of the coupleforces. The pipe is fixed supported at end B.
The bolted connection is subjected to a tensile force of P. The diameter of the bolt is d=60 mm. if P=200kPa. Determine the average shear stress (MPa) in the bolt.
Two forces of magnitude TA = 6 kips and Tc = 9 kips are. applied as shown to a welded connection. Knowing that the connection is in equilibrium, determine the magnitudes of the forces Tg and Tp- %3D 40 To Tc
In the assembly shown. the block has a weight w = 200 lbs and the cord is attached to the pin at B. The pulleys have radi of rt = 2 Tn. and r2 1 În. Neglect the mass of the pulleys and the link. Pulley Pulley A 45 12 Compute the reaction at the ĩnk AB In lbs." 250 260 280 B.