An efficiency consultant is studying the power stroke of a four-stroke engine and determines the following: 1. As the piston is forced down, the mixture of combustion products and air undergoes an adiabatic expansion. 2. The engine is running at 2,400 cycles/min. 3. The gauge pressure immediately before the expansion is 20.0 atm. 4. The volumes of the mixture immediately before and after the expansion are 50.0 cm³ and 400 cm³, respectively (figure below). 5. The time interval for the expansion is one-fourth the period of the cycle. 6. The mixture behaves like an ideal diatomic gas with a specific heat ratio of 1.40. Determine the average power (in kW) generated during the power stroke. kW Before -50.0 cm³ 400.0 cm³ After i

An efficiency consultant is studying the power stroke of a four-stroke engine and determines the following: 1. As the piston is forced down, the mixture of combustion products and air undergoes an adiabatic expansion. 2. The engine is running at 2,400 cycles/min. 3. The gauge pressure immediately before the expansion is 20.0 atm. 4. The volumes of the mixture immediately before and after the expansion are 50.0 cm³ and 400 cm³, respectively (figure below). 5. The time interval for the expansion is one-fourth the period of the cycle. 6. The mixture behaves like an ideal diatomic gas with a specific heat ratio of 1.40. Determine the average power (in kW) generated during the power stroke. kW Before -50.0 cm³ 400.0 cm³ After i

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

During the compression stroke of a certain gasoline engine, the pressure increases from 1.00 atm to 19.0 atm. The process is adiabatic and the air-fuel mixture behaves as a diatomic ideal gas. (a) By what factor does the volume change? Vfinal = Vinitial (b) By what factor does the temperature change? Tinal = Tinitial Assume the compression starts with 0.016 mole of gas at 28.5°C. (c) Find the value of Q that characterizes the process. (d) Find the value of AEnt that characterizes the process. (e) Find the value of W that characterizes the process.
8 An SI engine operating on stoichiometric propane fuel burns 0.00005 kg of fuel in each cylinder during each cycle with a combustion efficiency of 95%. When combustion starts at the end of compression, the temperature and pressure in the cylinder are T 700 K and P = 2000 kPa. Exhaust temperature leaving the cylinder after combustion is Tex = 1200 K. Calculate: 1. combustion heat input into each cylinder during each cycle using Q = E N,h; - E N,h, PROD REACT 2. heat input using Qin = nm,QLHV Indicate the source of the Tables of Properties used in your calculation. Assume Ah; = 29,711k] /kmol for %3D propane gas.
What energy conversion takes place in an internal combustion engine?
For a period of 0.2 hour of test, 620 grams of fuel with density of 875.4 Kg/m^3 at 37.5 degree-C are completely burned with air at air-fuel ratio of 14 Kg of air per one Kg of diesel fuel. The compression ratio is 14. Using a brake torque analysis, the dynamometer reads a scale of 85 Kg with 35 cm arm at 440 rpm. (i) Find the brake thermal efficiency of a supercharged 4-cylinder, 4 stroke cycle Diesel engine with a bore and stroke of 10cmx16cm. Note: recquires unit analysis
In an isochoric and isobaric combustion cycle, the indicated average pressure is 10 bars and the maximum pressure is 60 bars. The pressure and temperature at the start of the cycle are 1 bar and 17 oC. The volumetric compression ratio is 16/1. The mass constant of gas, R = 287 J / kg K The specific heat at constant volume, cv = 718 J / kg K. Calculate the maximum temperature of the combustion cycle for a thermal efficiency of 60%.
The spark-ignition engines run on a mixture of gasoline and air. The amount of mixture the engine can take in depends upon following major factors: (i) Engine displacement. (ii) Maximum revolution per minute (rpm) of engine. (Hi) Carburetor air flow capacity. (iu) Volumetric efficiency of engine. Explain each of the above factor in detail.
4Air enters the compressor of a simple gas turbine at p1 = 14 lbf/in2, T1 = 520°R. The isentropic efficiencies of the compressor and turbine are 83 and 87%, respectively. The compressor pressure ratio is 12 and the temperature at the turbine inlet is 2500°R. The volumetric flow rate of the air entering the compressor is 9000 ft3/min. Use an air-standard analysis. a) Determine the net power developed, in Btu/h. b) Determine the thermal efficiency of the cycle. c) The temperatures at the compressor and turbine exits in °R. d) The temperatures at the compressor and turbine enters in °R rmine the net power developed, in Btu/h .
Air enters the diffuser of a ramjet engine (schematic shown below) at 6 lbf/in.?, 420°R, with a velocity of 1800 ft/s, and decelerates essentially to zero velocity. After combustion, the gases reach a temperature of 2000°R before being discharged through the nozzle at 6 Ibf/in.2 Diffuser- Nozzle Flame holder On the basis of an air-standard analysis, determine: (a) the pressure at the diffuser exit, in Ibf/in.? (b) the velocity at the nozzle exit, in ft/s. Neglect kinetic energy except at the diffuser inlet and the nozzle exit. Assume combustion occurs at constant pressure and flow through the diffuser and nozzle is isentropic. AAA
Which of the following is the correct statement? a. Irreversible engines have maximum efficiency b. The increase in entropy is obtained from a given quantity of heat at a low temperature c. The entropy represents a maximum amount of work obtainable per degree drop in temperature d. All the reversible engines have the same efficiency e. All the reversible and irreversible engines have the same efficiency f. The change in entropy may be regarded as a measure of the rate of the availability of heat for transformation into work g. All engines are designed as reversible to obtain maximum efficiency
a petrol working on a constant volume cycle has a compression ratio of 9 to 1. if the pressure and temperature of the petrol-vapor mixture at the beginning of compression assuming it follows the law PV^1.4=C
Discuss the importance of the valve system in an internal combustion engines.
intake valve intake compression JO BI Tuel injector the temperature of the gas; power exnaust vaive 0010 exhaust The diagrams show the cylinder of a petrol engine in 4 stages. Petrol vapour and air are drawn into the cylinder, The mixture is then squeezed together, and then exploded by a spark. The explosion pushes down the piston. The exhaust gases are then expelled from the cylinder. Use the first law of thermodynamics to analyse the energy changes during the process. At each stage explain what happens to i) the pressure of the gas; ii)