A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m. The flow rate is 10-8 m³ / s. What is the viscosity of the fluid?

A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m. The flow rate is 10-8 m³ / s. What is the viscosity of the fluid?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In a given setup, distilled water flows towards the inside and goes outside of the vessel as shown in the figure. What is the rate of change of the water's mass (dm/dt) in the vessel? 3 in. Q = 0.3 ft3/sec V = 30 ft/sec Device m = 0.3 slug/sec %3D
A certain llquid flows In a 10mm dlameter smooth plpe that Is 20 m long. The total head lost in the pipe is 30 m and the Reynolds number is 1800. a. What is the friction factor f? b. What is the value of the kinematic viscosity of the liquid? c. What is the discharge?
Fluid is flowing through a 1000 mm diameter and 5200m long prototype pipe. The prototype is to be studied using a 40mm diameter pipe model. The fluid density in the prototype is 0.72 times the density of the fluid in the model, while the dynamic viscocity of the protype fluid is 1.86 times the dynamic viscosity of the model fluid. From the experiment performed on the model, the pressure difference is 250.5 kPa. wwwm Determine the pressure difference in the prototype if both must have hydraulic similarity.
Liquids A, B and C, in the containers shown, have SG of 0.60, 1.20 and 1.60 respectively. At what elevation (EL. A) will the liquid A stand in each of the piezometer tubes? Round your answer to the nearest hundredths. Pair = 12.5 kPa EL. 8 A (SG =) EL. 6 B (SG =_) EL. 2 C (SG =_) %3D EL. 0
A capıllary glass tube of 0.1 mm internal diameter is immersed vertically in a beaker full of waten Assuming the tube to be perfectly clean and wet, determine the height of the capillary rise of water in the tube when the room tamp is 20°C. Given at 20°C unit weight of water = 0.9980 gm/cc and surface tension 72.8 dyne/cm. %3D
2. A cylindrical tank 1.5m in diameter contains a column of 3 immiscible liquids with SG 0.8, 1.0, and 1.8. Each of the liquids have heights of 0.5m. There is a 50mm diameter orifice at the bottom of the tank. Solve the time needed to drain the first liquid, time needed to drain the second liquid, and time needed to fully drain the tank. Hint: For layered fluids similar to this problem, before plugging the given into the Bernoulli's Equation, you have to convert the heights of the other fluids to the equivalent height of the fluid that is presently being drained. Heights of different fluids are equivalent if they will result to the same pressure at the bottom. As an example, an 8m high water (SG = 1.0) will produce the same pressure at the bottom as a 10m high oil (SG = 0.8). Thus, an 8m high water is equivalent to a 10m high oil. Yoil hoil P = Yw hw =
Please solve chapter Analytical Positioning Reactions max 30-45 minutes thank u A beam with bearings A (rolls) and B (joints) is loaded as shown in the figure. Given : The working moment is 96 kNm at B, and the load is evenly distributed to the triangle acting 16KN/m on the high side of the triangle. Question: Calculate the magnitude of the deposition reaction at A and at B in an analytical way, include the units and indicate the direction of the reaction Note : In Image A = rolls B = pin/joints
Question 1 b) The U-tube manometer can be used to detemine pressure difference between two systems. This type of manometer is called a differential U-tube manometer. Consider the differential manometer connected to a pipe, as shown in Figure 1. Explain step by step on how you can calculate the pressure difference between point A and B. P1 h, A Flow Test Section U-Tube Differential Manometer
c) The orifice flowmeter shown in Figure 4 is used to obtain the flowrate of oil inside a conduit. The diameter of the orice, d is one third of the pipe diameter, D with pressure difference recorded as 25 kPa. The pipe diameter D is 6 cm, discharge coefficient Ca, is 0.60, Bis the ratio of orifice diameter to pipe diameter and Oilspedific gravity, SG is 0.95. If the h is 7 cm, i. Calculațe the vollime flowrate of oil inside the conduit. ii. Determine the mass flowrate of oil inside the conduit. iii. Explain why the discharge coefficient Ca, for the orifice meter is higher compared to the venturi and nozzle meters. D=6 cm d Figure 4
A concentric cylinder viscometer may be formed by rotating the innermember of a pair of closely fitting cylinders. The annular gap is small so that alinear velocity profile will exist in the liquid sample. Consider a viscometer withan inner cylinder of 4 in. diameter and 8 in. height, and a clearance gap widthof 0.001 in., filled with castor oil at 90_F. Determine the torque required to turnthe inner cylinder at 400 rpm.
A time independent non Newtonian fluid of density 0,00085kg/cm3 flows in a cylindrical pipe with a mean linear velocity of 1.70 m/s at steady state. The pipe is 3m long with an inside diameter of 0.075m. The point pipe consistency coefficient is 1.52 (N/m2)s0.3 and the flow behavior index is 0.3. Determine: a) The point values of the apparent viscosity. b) Reynolds Number. c) Pressure drop in Pascals.
1. A block, 1ft square and 9 inches deep floats on a stratified liquid composed of a 6in layer of water above a layer of mercury. Determine the weight of the block if the position of its bottom is 1 inch below the mercury. 2. At point A in a pipeline carrying water, the diameter is 1m, the pressure is 98kPa and the velocity is 1m/s. At point B, 2m lower than A, the diameter is 0.5m and the pressure is 20kPa. Determine the direction of flow. Show detailed computation. 3. What is the hydraulic radius of the channel shown: 1.5m 1.5h 4. wty A vertical right-angled triangular surface has a vertex in the free surface of a liquid. Find the force on one side. 1.5m 1:2m