A steel shaft of 75 mm diameter is pressed into a steel hub of 100 mm outside diameter and 200 mm long in such a man- ner that under an applied torque of 6 kN-m relative slip is just avoided. Find the interference fit, assuming a 75 mm common diameter, and the maximum circumferential stress in the hub. µ = 0-3, E = 210 GN/m².

A steel shaft of 75 mm diameter is pressed into a steel hub of 100 mm outside diameter and 200 mm long in such a man- ner that under an applied torque of 6 kN-m relative slip is just avoided. Find the interference fit, assuming a 75 mm common diameter, and the maximum circumferential stress in the hub. µ = 0-3, E = 210 GN/m².

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.8P: Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the...

See similar textbooks

Similar questions

Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
Repeat Problem 10.3-15 using L = 3.5 m, max = 3 mm, and EI = 800 kN·m2.
A winch raises a 60# bucket of paint, as shown. The main shaft of the winch is simply supported by bearings at A and C. The winch uses a 6"diameter pulley (B) and torque is applied at the end of the shaft to pull the cart. Determine the minimum shaft diameter based on the Distortion Energy (Von Mises) criterion using on a yield strength of 50ksi and a design factor of 2.0. 12" winch 18" C A Paint Rope
Two designs for shaft are being considered. Both have an outside diameter of 60 mm and are 500 mm long. One is solid but the other is hallow with an inside diameter of 40 mm, both are made from steel ( G=80 GPa). Compare the torsional shear stress, and the mass of the two designs if they are subjected to a torque of 71 N.m.
A hollow shaft has an inner diameter of 0.035 m and an outerdiameter of 0.06 m. Compute for the torque if the shear stress isnot to exceed 120 MPa in Nm.
A shaft made of steel receives 7.5 kW power at 1500 r.p.m. A pulley mounted on the shaft as shown in Fig. has ratio of belt tensions 4. The gear forces are as follows : F, = 1590 N; F, = 580 N Pulley Gear F1 A D F, -100 : 200- 100→ All dimensions in mm. Design the shaft diameter by maximum shear stress theory. The shaft material has the following properties : Ultimate tensile strength = 720 MPa; Yield strength = 380 MPa; Factor of safety = 1.5.
Bearing stress 5. Please provide proper discussion and illustration also complete solution and clear solution please thank you A solid shaft is designed to transmit 50kN @ 1800 rpm to a gear by means of 156 mm long key with square cross-section. The shaft diameter is 35.6mm. What should the cross-section be in mm2 to resist shearing, if the allowable shear stress on the key is 20 MPa?
The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted. Q2 Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be takenas 1.5. Q3 a) An universal coupling is used to connect two mild steel shafts transmitting a torque of 6000 N- m. Assuming that the shafts are subjected to torsion only, find the diameter of the shaft and the pin. The allowableshear stresses for the shaft and pin may be taken as 55 MPa and 30 MPa respectively.
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
A drive shaft running at 2500 rpm has outer diameter of 60mm and innerdiameter of 40mm. The allowable shear stress in the shaft is 35MPa. Determine themaximum power that can be applied. Present drawings/FBD’s illustrating your solution.