A liquid-level system has the following properties: Tank dimensions: 10 ft high by 5-ft diameter Steady-state operating characteristics: Inflow, galh Steady-state level, ft 5,000 0.7 10,000 1.1 15,000 2.3 20,000 3.9 25,000 6.3 30,000 8.8 The inlet flow rate is held at 300 gal/min for 1 h and then suddenly raised to 400 gal/min. Assuming that linear interpolation is valid within inflow interval, determine the liquid-level 0 minute after the sudden increased in flowrate.

A liquid-level system has the following properties: Tank dimensions: 10 ft high by 5-ft diameter Steady-state operating characteristics: Inflow, galh Steady-state level, ft 5,000 0.7 10,000 1.1 15,000 2.3 20,000 3.9 25,000 6.3 30,000 8.8 The inlet flow rate is held at 300 gal/min for 1 h and then suddenly raised to 400 gal/min. Assuming that linear interpolation is valid within inflow interval, determine the liquid-level 0 minute after the sudden increased in flowrate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Pelton wheel operates from an effective head of He = 450 m and at a flow rate of 5.0 m³/s. The wheel radius is r2= 0.85 m and its rotational speed is 430 rpm. The water which leaves the penstock is divided into a few streams. The nozzle coefficient is CN = 0.98 for each of the nozzles. Impulse blades turn the flow into the direction ß3 =-62° and as a result of friction the relative velocity reduces by an amount which gives a velocity coefficient cv = 0.96. Find, (a) the efficiency of the turbine, (b) the power specific speed, (c) the jet number, d) the nozzle diameter e) the number of buckets in the wheel. First find the exit velocity from the nozzle and the blade speed; V2 = CN V29H. U = r,N Туре Ssp | n % The relative velocity entering the Wheel; W2 = V2 – U Pelton wheel 88 – 90 Single jet Twin jet Three jet Four jet 0.02 - 0.18 Relative velocity at the exit; 0.09 – 0.26 89 – 92 W3 = c,W2 0.10 – 0.30 89 – 92 0.12 – 0.36 86 The tangential component of the relative velocity at the…
An aqueduct is required to supply water to the community.Data: Families = 12 Average members per family = 3 people Breakfast, lunch and dinner = 15 total liters / family Showers = 10lt / person, one daily shower Kitchen wash = 13lts / day Total distance of the pipeline to the storage tank = 1200 meters Total height H from the pump point to delivery to the tank = 70 meters Determine: Estimation of the total volume of the recommended tank, an autonomy of at leas 2 days of storage. It is required to propose a pump that allows at least filling the tank between 5 to 12 hours operation, it must include details of the pump, as well as its curve Image: schematic detail of the proposed system
oblems: 1. A horizontal pipe, 1 ft. in diameter, tapers gradually to 8 in. in diameter. If the flow is 500 cu ft. of water per minute, what is the difference between the pressures at the two sections? Ans. PA - PB = 443.63lb per sq ft 2. Water flows through a horizontal pipe at a velocity of 50 ft. per sec. Owing to the pipe gradually expanding to a larger size, the velocity decreases to 35 ft. per sec. What is the difference between the pressures at two points, one in each size of pipe? Ans. Pg - PA = 1,236. 75 lb per sq ft
5. The total head of a fan is 185 m and has a static efficiency pressure of 210 mm of water gage.What is the velocity of air flowing if the density of air is 1.15 kg per cubic meter? 8. A coal fired steam boiler uses 3000 kg of coal per hour. Air required for combustion is 15.5 kg ofcoal at barometric pressure of 98.2 KPa. The flue gas has temperature of 285 degree Celsiusand an average molecular weight of 30. Assuming an ash loss of 11% and allowable gas velocityof 7.5 meters per second. Find the diameter of the chimney 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of…
Example 1: A system has a volume flow rate requirement of 1lit/s with an index run AP of 30kPa. Find an appropriate pump from the A manufacturer's catalogue gives the following information for a centrifugal pump operating at 12rev/s: P| 49.38 47.5| 44.38 40 34.38 27.5 19.38 Q|0.25 0.5 0.75 1.25 1.5 1.75 yelume flow rate
2. The initial condition of air in an air compressor is 99 kPa and 30 deg. C and discharges at 438 kPa. The bore and stroke are 374 mm and 395 mm, respectively. The percent clearance of 11 % running at 356 rpm. Find the volume of air at suction in m^3/s ANswer in one decimal places
Please solve it correctly,Urgent. Question: The discharge pressure of a water pump is 9, 000 kPa. The temperature is 150 deg deg C and density is 917 kg/m3. What is the equivalent pump head in meters? A. 11.005 m B. 1,000.5 m C. 1,050.5m D. 1, 100.5 m
1. Ifa pump discharges 70 GPM of water whose specific weight is 61.5 lb/ff° at local g= 31.9 t/s, find a. Mass flow rate Ib/min b. Time to fill a drum 100 in. diameter and 12 ft high, min.
71. Find the inlet cross-sectional-area for an airplane engine (p, = 1.31 p2, P2 = 99.8 kPa, T2 = 232 °C, v, = 109 m-s1, v2 = 811 m-s1, A2 = 0.7 m?, Fth = 33 kN). png càug yảào %3D %3D %3D == ===
An induced draft fan handles 63,500 cfm in of flue gas with a gas constant of 51.5116 ft-lb / lb-R from a boiler at 500 degrees Fahrenheit against a static pressure of 4in. water. The discharge duct diameter is 73.67in. The barometric pressure is 29.9” Hg. Determine the following: a. the total head in ft. of water b. the Air Power in horsepower
Problem-4: The characteristics for a pump are given in the table below. The pump is required to left water against static head Az = EN" m. The pipe arrangement has a total length L the pump discharge, head, efficiency and power for the given pipe system. 200, d = 0.1 m and f= 0.016. Find %3D Q (L/s) 10 20 30 35 42 50 Hp (m) efficiency % 210 201 180 150 129 93 48 30 58 80 85 86 74 EN=62 Hp = Az + h, = Az + 12.1 d P = 757
1. Specify the sizes of pipes (cast iron, schedule 40 ) and the size of the motor to be used for a pump to lift water at 50 from reservoir A to reservoir B. Consider the following data: Total static head Fittings and valves: Suction line Discharge line Length of straight pipe: Suction pipe Discharge pipe Absolute viscosity of water Absolute roughness of cast iron Water velocity 50 m 1 foot valve, 1 standard elbow 1 gate valve 1 check valve (same as close return valve), 1 gate valve, 1 long sweep elbow, 2 standard elbow 300 m 80 m 0.001002 Pa-s 0.00026 m m 1.18 -2.75 S Pump efficiency 80% Note: Neglect the head loss in the foot valve and at the pipe exit in the discharge reservoir and do not equal sizes for the suction and discharge pipes. Draw the piping system.