A flagpole 16 m high has the shape of a cylinder 100 mm in diameter. The air temperature is 30°C and the atmospheric pressure is 101 KPaa. With what speed is the air blowing against the pole if the moment developed at the base is 2.7 KN.m? The drag coefficient is 1.3.

A flagpole 16 m high has the shape of a cylinder 100 mm in diameter. The air temperature is 30°C and the atmospheric pressure is 101 KPaa. With what speed is the air blowing against the pole if the moment developed at the base is 2.7 KN.m? The drag coefficient is 1.3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3) An advertising sign mounted on the roof of a car is 33 inches tall, 15 inches wide and 54 inches long (airflow direction). The underside of the sign is flush with the top surface of the roof. Take air properties to be: p = 0.075 lbm/ft' and u= 1.22x10 lbm/ft.sec. Used a pressure drag coefficient of 1.2 for the advertisement sign. Calculate the total drag on the sign and the power required to overcome its effect if the car is travelling at a constant speed of a) 12 mph and b) 45 mph. Note: Provide a schematic diagram (sketch) of the problem configuration (if applicable). Every numerical calculation must be preceded by the appropriate equation. Do not forget units & dimensions during your calculations.
The drag coefficient for a car with a frontal area of 26 ft? is being measured in an 8 ft x 8 ft wind tunnel. The density of air under the test conditions is 2.4 x 10 3 slugs/ft, When the air flow rate is, 500,000 ft/min, the drag force on the car was measured to be 170 lb. The drag coefficient under the test conditions is most nearly O 0.30 O 0.32 O 0.28 O 0.34
An antenna in the shape of a cylindrical rod projects from the top of a locomotive. If the antenna is 42 in long and 0.200 in. in diameter, compute the drag force on it when the locomotive is traveling at 160 mph in still air at -20°F.
The original Flettner rotor ship was approximately 100 ftlong, displaced 800 tons, and had a wetted area of 3500 ft2. Assketched in Fig. , it had two rotors 50 ft high and 9 ft indiameter rotating at 750 r/min, which is far outside the range. The measured lift and drag coefficients for eachrotor were about 10 and 4, respectively. If the ship is mooredand subjected to a crosswind of 25 ft/s, as in Fig. whatwill the wind force parallel and normal to the ship centerlinebe? Estimate the power required to drive the rotors.
If the pressure difference in the wind tunnel experiment is 50 mmH,0, the density of air is 1.2 kg/m in wind tunnel experiment, and the airfoil span is 204 mm, and the cord length is 98 mm, what is the lift coefficient if the lift force is L=13.4 N
The wing loading on an airplane is defined as the aircraft weight divided by the wing area. An airplane is cruising with a wing loading of 2500 Pa. The lift coefficient and drag coefficient are 0.30 and 0.06, respectively. Calculate the drag force if the wing planform area is 12 m2. Assume that the air density is unknown and not given.
The drag polar equation of a light airplane in clean configuration can be written as Cp = 0.358 + 0.0405 C₁². It has a weight of 18,681 N. The wing area is 14.41 m². Calculate the minimum power required in watts. (Round off answer with no decimal places, No units, No commas) Answer given: 1461792 A 5,000 lbs. aircraft has an excess power of 75 hp at sea level. If the service ceiling is 3,657.6 m, determine the time to climb from sea level to absolute ceiling in minutes. (Round off answer with no decimal places. No units, No commas) Answer given: 17
Fluid Mechanics Problem: A ship is 150 m long and has a wetted area of 5000 m2.If it is encrusted with barnacles, the ship requires 7000 hp to overcome friction drag when moving in seawater at 15 kn and 20oC. What is the average roughness of the barnacles? How fast would the ship move with the same power if the surface were smooth? Neglect wave drag. Note: Treat the ship hull as a flat plate. Use eq. 7.48b to find effective barnacle roughness height.Use equation (7.45) White for the drag coefficient CD = D/.5pV2A , where A is the hull (plate) area, to find the ship velocity for smooth plate.
A ship is 150 m long and has a wetted area of 5000 m2.If it is encrusted with barnacles, the ship requires 7000 hpto overcome friction drag when moving in seawater at 15 kn and 20°C. What is the average roughness of thebarnacles? How fast would the ship move with the samepower if the surface were smooth? Neglect wave drag.
In the vertical wind tunnel used in paratrooper training, find the wind tunnel free speed required to keep a 75 kg person suspended in the air in a horizontal position. The height of this person is 1.7m and the width is 38cm and the front drag coefficient is around 1. Atmospheric pressure and temperature inside the tunnel are Patm = 85kPa and T = 25C, respectively.
A rotary mixer is constructed from two circular disks as shown. The mixer is rotated at 60 rpm in a large vessel containing a brine solution (SG = 1.1, μbrine=1.07×10-3 Pa-s). Determine the appropriate coefficient of drag using Low Reynolds Drag Coefficient. Neglect the drag on the rods and the motion induced in the liquid. Estimate the minimum torque and power required to drive the mixer. only HANDWRITTEN answer needed ( NOT TYPED)
For a 10 deg included angle wedge at 0 deg AOA, calculate the lift and drag coefficient (Cl = 0, Cd = 0.082). Then calculate the lift and drag at AOA=4 deg (Cl = 0.16, Cd = 0.093). Let M=2.