A conical clutch has an inclined angle of 120. The outer and inner diameters are 80 mm and 20 mm respectively. Calculate the force required to press the two halves together if it is to transmit 200 W at 600 rev/min. The coefficient of friction is 0.3. Use both the uniform wear theory and the uniform pressure theory.

A conical clutch has an inclined angle of 120. The outer and inner diameters are 80 mm and 20 mm respectively. Calculate the force required to press the two halves together if it is to transmit 200 W at 600 rev/min. The coefficient of friction is 0.3. Use both the uniform wear theory and the uniform pressure theory.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 3 An engine of a 2 ton truck develop 30 kW at 600 rpm. The truck is fitted with a cone clutch to increase torque. The cone clutch has an outer diameter of 500 mm and inner diameter of 300 mm. the cone has a face angle of 12.5° and a width of 45 mm. The coefficient of friction of 0.25 and normal pressure on the clutch face is not to exceed 0.1 N/mm? 3.1. Sketch the cone clutch and indicate all dimensions and forces. 3.2. Calculate the axial thrust. 3.3. Calculate axial spring force to engage. 3.4. Derteimine the wear. 3.5. Find torque.
A conical clutch has an included angle of 120°, a coefficient of friction of 0.4, and outer and inner diameters of 85mm and 18mm respectively. Using both the uniform wear theory and the uniform pressure theory, calculate the force required to press the two halves together if it is to transmit 300W at 750rev/min. The uniform wear theory and the uniform pressure theory deliver different values for torque in the same system. Which theory would be preferred in practice for use in calculations involving a friction clutch? Give reasons for your choice.
A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250 mm and the inner diameter is 150 mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75 kW at 500 r.p.m. Assume uniform wear and coefficient of friction as 0.3.
A cone clutch with a cone angle of 12° transmits 53 kW at 1300 rpm. The coefficient of friction of linings is 0.16. Determine the axial spring force necessary to engage the clutch in N if the mean diameter of the active conical sections is 250 mm.
A cone clutch has cone elements at an angle of 12o. The clutch transmit 25 HP at a speed of 1200 rpm. The mean diameter of the conical friction section is 16 in and the coefficient of friction is 0.35. Find the axial force needed to engage the clutch.
multi-disc clutch has three discs on the driving shaft and two on the driven shaft. The inner diameter of the contact surface is 120 mm. The maximum pressure between the surface is limited to 0.1 N/mm . Find the outer diameter for transmitting 25 kW at 1575 rpm . assume uniform wear condition and coefficient of friction 0.3.
A conical friction clutch is used to transmit 70 kW at 1000 rpm. The semicone angle is 20° and the coefficient of friction is 0.2. If the outer diameter is 400 mm and the inner diameter is 340 mm and the intensity of normal pressure is not to exceed 0.20 N/mm². Determine the axial Force (F) required in Newton (N)
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
4. A friction clutch is required to transmit 34-5 kW at 2000 rev/min. It is to be of single-plate disc type with both sides of the plate effective, the pressure being applied axially by means of springs and limited to 70 kN/m². Ifthe outer diameter of the plate is to be 300 mm, find the required inner diameter of the clutch ring and the total force exerted by the springs. Assume the wear to be uniform. µ = 0-3. (U. Lond.) (Answer: 200 mm; 2-2 kN)
A multiple V-belt drive is required to transmit 4 kW. The smaller pulley of the system is150 mm diameter, rotates at 200 rev/min, and has an angle of lap angle of 135°. Thegrove angle is 40° and the coefficient of friction between the belt and the pulleys is 0·3.If the maximum tension in any one belt is limited to 800 N, calculate:(a) The number of belts required. (b) The minimum tension in any one belt. (c) The required pre-tensioning of the belt. The centre-to-centre distance between the pulleys is 2 m.(d) Determine to the nearest mm, the required size for the larger pulley.(e) Find the approximate length of the belt
A car engine has its rated output of 120 kW. The maxdmum torque developed is 110 Nm, The clutch used is of single plate type having two active surfaces. Axia! pressure is not to exceed 0.85 bar. External diamater of friction plate is 1.25 times the internal diameter. Determine the dimensions of friction plate and axial force exerted by the spring. Assume uniform wear and coefficient of friction to be 0.3.
A multiple friction clutch is required to transmit 89.52 kW at 3000 rpm. The plates are alternatively of steel and phosphor bronze and they run in oil. The coefficient of friction is 0.08. The internal radius of the friction surface is 0.8 times the radius of the external surface. The axial pressure is limited to 20 x 104 N/m2. If the maximum diameter of the frictional surface is not to exceed 250 mm, determine the number of plates required.