(a) A 400 mm length of conductor carrying a current of 25 A is situated at right-angles to a magnetic field between two poles of an electric motor. The poles have a circular cross-section. If the force exerted on the conductor is 80 N and the total flux between the pole faces is 1.27 mWb, determine the diameter of a pole face.

(a) A 400 mm length of conductor carrying a current of 25 A is situated at right-angles to a magnetic field between two poles of an electric motor. The poles have a circular cross-section. If the force exerted on the conductor is 80 N and the total flux between the pole faces is 1.27 mWb, determine the diameter of a pole face.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.1MCQ: The Ohms law for the magnetic circuit states that the net magnetomotive force (mmf) equals the...

See similar textbooks

Similar questions

The applied MMF to a simple magnetic circuit is 350AT. It was found that the resulting magnetic field denstiy is 0.7 Wb/m2. The average length of this magnetic circuit is 1.64ft and its cross-sectional area is 4cm². What is the relative permeability of the magnetic material of the core?
B. For the following magnetic circuit, the flux passing through the core is 1.32 mWb, the cross section of the core is 3 cm by 4 cm, the laminated section has a stacking factor of 0.9, and the gap is 1 mm. Determine the flux density in each section. Neglect fringing d N turns Cast iron Air gap Laminated sheet steel
A rectangular coil of wire has a length of 3 cm and a width of 4 cm. It is in a 0.004 T magnetic field. What is the magnetic flux through the coil if the face of the coil is parallel to the B-field lines? What is the flux if the angle between the face of the coil and the magnetic field is 75°?
The applied MMF to a simple magnetic circuit is 350AT. It was found that the resulting magnetic field denstiy is 0.7 Wb/m². The average length of this magnetic circuit is 1.64ft and its cross sectional area is 4cm². What is the reluctance (in AT/Wb) of the magnetic material of the core?
An iron circuit with a small0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm2, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (u, = 800 for iron). Figure 1
A magnetic circuit with a cross-sectional area of 20 cm? is to be operated at 50 Hz from a 120 V rms supply. The number of turns required to achieve a peak magnetic flux density of 1.8 T in the core is
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm?, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron). Figure 1
4. A magnetic circuit has a length of 100 cm and cross-sectional area of 5 square cm. The total flux is 10 x 10* webers. The coil has 100 turns and current of 4 amperes. What is the magnetic strength? a. 500 AT/m b. 400 AT/m c. 350 AT/m d. 450 AT/m
Consider an iron ring of 10 cmdiameter is uniformly wounded with 3000 turns of wire. The coil current is 0.25 A and a flux density of 0.6 T is set in the ring. Determine the relative permeability of the iron and magnetic field strength.
In the core of a long solenoid the magnetic flux density is 100 Tesla. The cross section of the solenoid is a circle with diameter d=10 cm. Determine the magnetic flux in the core in mWb.
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm², and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (ur = 800 for iron).
In the figure is shown a current of 50 A in a wire 120 cm long and at an angle of 45° to a magnetic field of flux density 6.0 x 10 -4 Wb/m2. What are the magnitude and direction of the force on this wire?