5. The rectangular section of the following column is subjected to a compressive 150 kN force on its corner "A". Compute the stresses at each of the 4 corners of the section, and sketch a 3D distribution of the stresses. at each corner 30 stress distribution 100 mm D 150 KN 2% A B 150mm REQ'D - Stress

5. The rectangular section of the following column is subjected to a compressive 150 kN force on its corner "A". Compute the stresses at each of the 4 corners of the section, and sketch a 3D distribution of the stresses. at each corner 30 stress distribution 100 mm D 150 KN 2% A B 150mm REQ'D - Stress

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Cross section of each bar 350 mm2 . Find stress in bar CD
An embedded beam is subjected to the loads shown. Determine the stress produced at points A, B ,C, D in the embedment section. The X axis is 72.9 mm from the top edge. Solve correctly please
Angle 1 Tyx Txy x-direction stress 60OMPA(compression), y-direction stress 40MPA(compression), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: Using a Mohr circle determine the stresses on the plane of the indicated angle 1. (50°). Show al calculations. Draw the orientation of the stress block for this scenario.
Find the diameter of dAB dec bar if the stress equal to 0.15GPA C 120cm B 125kN 125KN 90cm A 60kN
Determine principal stress and draw mohr circle
Question 3 Shear stress is directly proportional to the width of a section. O True O False
The unknown load P is acting eccentrically with respect to the horizontal and vertical axes of the I-section shown. Knowing that the horizontal eccentricity is a = 1.25 in. and the vertical eccentricity is 2.5 in. determine the largest value of P that can be applied without exceeding either of the following tensile andcompressive allowable stresses:σten = 10 ksiσcomp = 18 ksi
The cross section of a concrete corner column that is loaded uniformly in compression is shown in thefigure.a) Determine the average compressive stress (psi) in the concrete if the load is equal to 3 kips.b) Determine the coordinates x-bar and y-bar of the point where the resultant load must act in order toproduce uniform stress in the column. M=90N=43O=44P=45Q=44R=92
Part A The corners of the square plate are given the displacements indicated with di = 0.40 in. and d2 = 0.64 in. (Figure 1) Determine the shear strain at A relative to axes that are directed along AB and AD. Express your answer to three significant figures and include appropriate units. i HẢ (Yay)A = Value Units Submit Request Answer Part B Figure < 1 of 1 Determine the shear strain B relative to axes that are directed along BC and BA. Express your answer to three significant figures and include appropriate units. d, 12 in. 12 in. HA ? 12 in. (Yey)B = Value Units Submit Request Answer 12 in. < Return to Assignment Provide Feedback
1. A stepped cyllindrical bar carries axial forces as shown. What is the maximum value of P for stresses not to exceed 100 MPa in tension and 120 MPa in compression? AAB = 360mm2 ABC = 240mm2 ACE = 300mm2 5P 4P 3P A B C D 3P E חו P
2. A whole is to be punched out of a plate having a shearing strength of 298 MPa. The compressive stress in the punch is limited to 372 MPa. a. Determine the thickness of the plate if the hole to be punch is 76 mm in diameter. b. If the plate is 10mm thick, determine the diameter of the smallest hole that can be punched. P
The Mohr's circle shown has coordinates X = (60 MPa, -16 MPa) and Y = (0 MPa, 16 MPa). Draw the stress element for maximum shear at the correct orientation (label the new axes, the magnitude and direction of the stresses and show the angle). (Upload your answer showing all values as well as neat and clear calculations) Y