4. The pressure in a stationary liquid depends on the position below the surface z according to p(2) pg2, where p is the density of the liquid and g is the acceleration due to gravity. A planar dam of width w separates water of depth d from air. = (a) The force exerted by the water on the dam. (b) The moment exerted by the water about the central point O of the base of the dam. d Side view 2 Top view W

4. The pressure in a stationary liquid depends on the position below the surface z according to p(2) pg2, where p is the density of the liquid and g is the acceleration due to gravity. A planar dam of width w separates water of depth d from air. = (a) The force exerted by the water on the dam. (b) The moment exerted by the water about the central point O of the base of the dam. d Side view 2 Top view W

Name: 4.The pressure in a stationary liquid depends on the position below t
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 4.The pressure in a stationary liquid depends on the position below the surface z according top(2) pg2, where p is the density of the liquid and g is the acceleration due to gravity. Aplanar dam of width w separates water of depth d from air.=(a) Th

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the water, a square plate with (side= a) is lying vertically, with its upper horizontal edge touching the water's surface. The positions of the centre of pressure (h*) on the planar surface and the total pressure force (P) will be determined by: [Where, p is the density of water (a) P=pga/2, h=2/3.a (b) P=pga¹/2, h=2/5.a (c) P pga/4, h-2/5.a (d) P=pga/3, h=2/3.a (e) P=pga¹/5, h=2/7.a
A micircular gate with a radius R = 5 ft is hinged along B and held by a horizontal force applied at A. The picture on the right shows the gate if you were looking in the direon of the arrow beneath FA. The liquid has a depth of H=40 ft and applies a force on the ate of 200,032 lbf. What is FA in Ibf? FA A Gate: side view
Exercise 2 We want to determine the density p, of a liquid L2. To do this, let's pour water into a bath which will be placed in contact with a vertical wall of width b= 100cm and height h = 2m. The free surface of the liquid L2 is located at a distance a=700mm from the free R Liquid The Z Water X 1/a-Determine the resultant of the pressure forces R, exerted by the water on the vertical wall. b-Determine the position Ze of the center of thrust of this resultant. 2/ a- Determine the resultant of the pressure forces R. exerted by the liquid L, on the vertical wall as a function of p2. b-Determine the Zez position of the center of thrust of this resultant 3/ Determine the force F exerted by the air on the non-wet part of the vertical wall. 4/ By balancing the vertical wall, deduce the density p. of the liquid L2.
h = 4 ft F 2 ft A hemispherical glass bubble is installed in the side of a tank as a viewing window with its center 4 ft below the surface of the water. What is the magnitude of the vertical component of the force on the glass in lbs? The specific weight of water is 62.4 lbf/ft3.
Fluid mechanics В FB 1.8 m Water Gate A Hinge A 5.5-m-long (in directen normal to this page) quarter circular gate of radius l-8m is hinged at A as shown Frg ure · Neglecting the weight of the gate and the hinged, determine a) The magnitude and direction of the resultant force to the water. the "gate due on The horizontal force Fe that must be apphed în place to hold the gate the density of water to be 1000 kg/m³ and the gravita fronal constant to be - 9:9.81 m/s² Take
A fluid filled container is shown below. Oil fills the left side of the “U” to a depth of 33.0 cm while water fills the rest. The oil has a density of 753 kg/m3. The radius of the tube on the left side is 27.0 cm and the radius of the tube on the right side is 38.0 cm. a. If the height of the fluid in the two cylinders is exactly the same, what mass should be placed on the left cylinder to balance the system. b. What is the pressure at the bottom of the oil when the system is balanced? c. If the mass on the left is removed, what is the difference in heights between the two sides?
1. Consider a conic reservoir of unit depth that is initially filled with water at the height of h = 200 mm. A rigid cuboid block, with dimensions of 10 cm x 5 cm x 3 cm, is then dropped into the water. When the equilibrium state is reached, the block floats on the water's surface, as shown in the figure. If the specific gravity of the block is 0.5, determine the change in the free surface position of the water, i.e., Ah, in mm. %3D Hint: You can calculate the volume of liquid inside the conic reservoir with a unit depth in terms of the liquid height as V = th³/3. Ah block water water
A 12.5 kg block of metal measuring 12.0 cm by 10.0 cm by 10.0 cm is suspended from a scale and immersed in 5.60 cm below the surface of the water. Scale a b (a) What are the magnitudes of the forces (in N) acting on the top and on the bottom of the block due to the s significant figures.) Frop N N Fbottom (b) What is the reading of the spring scale (in N)? N (c) Show that the buoyant force equals the difference between the forces at the top and bottom of the block. ( II
A. Q4 A piston of cross-sectional area a is used in a hydraulic press to exert a small force of magnitude f on the enclosed liquid. A connecting pipe leads to a larger piston of cross-sectional area A (Fig.14-36).(a) What force magnitude F will the larger piston sustain without moving? (b) If the piston diameters are 3.80 cm and 53.0 cm, what force magnitude on the small piston will balance a 20.0. larg piston -> Small piston a
Q5 A U-tube manometer similar to that shown below is used to measure the gauge pressure of water (mass density p = 1000 kg /m3). If the density of mercury is 13.6 x 103 kg /m³, what will be the gauge pressure at A if h1 = 0.45 m and D is 0.7 m above BC. Wwater Wmercury
tank holding oil (SG=0.90) with its top surface open to the atmosphere is shown below. determine the magnitude and line of action of (a) the horizontal component (Fh) and (b) the vertical component (Fv) of the resultant force (Fr) exerted by the curved surface BC on the fluid. The tank is 4m deep, 2m wide, and R=1.5m. (c) Determine the magnitude and line of action (angle of inclination relative to the horizontal) of the resultant force, Fr
A closed tank whose bottom is 18 inches in diameter is filled with three liquids: 4 inches of carbon tetrachloride (SG=1.59), 2 inches of water and 12 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 1296 psf. d. Apply the PANEL EQUATIONS to determine the magnitude, direction and location of the total hydrostatic force acting at the bottom of the tank.