20 A, 40 A, 50 A and 30 A are tapped at distances of 100m, 250m, 400m and 5O0m from theend A respectively. If the area of X- section of distributor conductor is 1cm2, find the minimum consumer voltage. Take p .= 1:7 x 10-6 cm E A-110 F 4-140 B 100 m A 1-20 D 1-60 100 m 150 m 150 m 100 m 220 V 220 V 20 A 40 A 50 A 30 A

20 A, 40 A, 50 A and 30 A are tapped at distances of 100m, 250m, 400m and 5O0m from theend A respectively. If the area of X- section of distributor conductor is 1cm2, find the minimum consumer voltage. Take p .= 1:7 x 10-6 cm E A-110 F 4-140 B 100 m A 1-20 D 1-60 100 m 150 m 150 m 100 m 220 V 220 V 20 A 40 A 50 A 30 A

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 4PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

A 2 wire d.c. ring distributor is fed at A with 220 V. The various loads are 10A at B, 20A at C,30A at D and 10A at E. The resistances of the sections AB, BC, DC, DE and EA are 0.1 £2, 0.05 $2, 0.01 2, 0.025 2 and 0.075 respectively. Determine, a. Point of minimum potential b. Current in each section [Ans.: Point C, 29.04 A, 19.04 A, 0.96 A, 30.96 A and 40.96 A
The principle operation of LVDT is based on the variation of Select one a. Self inductance b. Reluctance c. Mutual inductance d. Permanence
Which of the following statement is true? a. Angle between load voltage and load current in a pure capacitive load is 45 degree. b. Angle between load voltage and load current in a pure capacitive load is is 180 degree. c. Angle between load voltage and load current in a pure capacitive load is is zero. d. Angle between load voltage and load current in a pure capacitive load is is 90 degree.
If we increase the load than core loss and copper loss will... Decrease Increase Remain same
W1 A 1 IL Tr1 AC Supply V V w2 12 Tr2 use double range voltmeter Fig.(1)
A 2-wire D.C. Ring distributor is 300 m long and is fed at 240 V at point A. At point B, 150m from A, a load of 120A is taken and at C, 100m in the opposite direction, a load of 80A is taken. If the resistance per 100m of single conductor is 0.03 Q, Find the voltages at all loading points and find the power dissipated in the distributor. Clearly draw the distributor, show all currents and loading points. BIEE Paragraph
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
Derive the formula and relation for voltage and current in a pure resistive- AC circuit and prove that in this type of circuit, the current and the voltage are always in phase.
A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the source voltage and the current through the circuit? a. Insufficient information is given. b. The source voltage will lag the current. c. The source voltage will lead the current. d. The source voltage will be in-phase with the current.
There era two type of currents, a. direct current and b. alternating current. For each of these type, name as many as you can the specific application and discuss them as to their effectiveness And safety.
2.)What is the difference between Ampere's law and Biot-Savart's law?
Consider Two same size series connected PV modules,each with the specification as Po=100W, Voc= 24.5V and Isc=5A.then choose the correct Statement Refer to this PV Panel. a.The output power from this panel is 100W , the Voltage is 24.5V and the current is 10A b.The output power from this panel is 200W , the Voltage is 24.5V and the current is 10A c.The output power from this panel is 200W , the Voltage is 49V and the current is 5A d.The output power from this panel is 200W , the Voltage is 49V and the current is 10AClear my choice