2. A square footing has a dimension of 1.8 m x 1.8 m x 0.8 m. The column section is 320 mm square. Using a minimum steel covering of 70 mm and fc' = 27.6 MPa, fy = 410 MPa. a) Determine the development length furnished. b) Determine the appropriate size of steel bars needed to conform to the development length requirements. c) Determine the minimum development length required if it is reinforced with 25 mm diameter bars.

2. A square footing has a dimension of 1.8 m x 1.8 m x 0.8 m. The column section is 320 mm square. Using a minimum steel covering of 70 mm and fc' = 27.6 MPa, fy = 410 MPa. a) Determine the development length furnished. b) Determine the appropriate size of steel bars needed to conform to the development length requirements. c) Determine the minimum development length required if it is reinforced with 25 mm diameter bars.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

QUESTION 2 a. A column 425 mm x 425 mm carries a characteristic axial load of 800 kN dead and 300KN imposed. A footing size of 2800mm x 2800mm and thickness of 500mm has been proposed, The allowable bearing pressure of the soil is 200KN/m2. You are required to: (i) check the suitability of the size and design the base against bending, punching shear (ii) Show in a sketch the reinforcement details provided.
The wall footing shown in the figure is subjected to an ultimate linear load of Pu = 180 kN/m. The wall thickness is 97mm, thickness of footing is 300 mm, and width of footing is L = 1000 mm. What is the exact spacing of 10 mm main rebars based on flexural requirements of NSCP 2015? Consider as singly reinforced with f'c = 28 MPa and fy = 275 MPa. The Pu already includes the weight of the footing and soil. Pu NGL
Design a square pad footing with an overall depth of 600mm, cover to the reinforcements 50mm with 20mm diameter reinforcement bars in both directions. The footing carries a 400mm square column with a dead load of 1050KN and imposed load of 300KN. The safe bearing capacity of the soil is 170KN/m^2, fcu 30N/mm^2. Assume a unit weight of concrete to be 24KN/m^3 and footing weight 150KN
Design a square reinforced concrete footing to support a 20-inch square tied concrete column at the edge of the building as shown below. Also check development length and force transfer in the column and at the footing. Draw the reinforcement pattern. Use a footing thickness of 24". Assume the following design conditions: -service dead load= 270 kips -service live load= 135 kips -allowable soil pressure (q)= 5000 psf -f. for the column= 5000 psi -f. for the footing= 3000 psi -fy= 60000 psi -longitudinal column steel consists of #8 bars reinf cement is uncoated -unit weight of the soil is 125 lb/ft3 -normal weight concrete Finished ground line 20" square column Y = 125 lb/ft³ 5'
ASAP PLS I GIVE UPVOTE If the square footing has an 800mm edge with a 300mm thickness, and that the 200mm x 200mm column has a 1.1m height from the top of the footing up to the finished ground line are both constructed, how much gravel (in m3) should be exactly used for a class B concrete mixture for the footing and the column (up to the finished ground line level).
A3 mx 3 m square spread footing is to support a 350 mm x 350 mm column carrying a dead load of 750 kN and live load of 500 kN. For concrete f'c is 21 MPa and for steel, fy is 415 MPa. Use NSCP 2001 provisions. Determine the effective depth considering punching shear. A 300 mm 350 mm 400 mm 450 mm B.
Design round column footing for 18 in diameter that supports loads of PD = 240 k and PL = 140 k. The bottom of the footing is 6 foot below final grade, reinforced concrete weight is 150 lb/ft3 and the soil weighs 100 lb/ft3 the allowable soil pressure is 5 ksf. The concrete strength is 4,000 psi and the steel is Grade 60. 2
B Jf g is the punching shear resistance per unit area a, is the side of a square footing for a column of side b, carrying a weight W including the weight of the footing, the depth (D) of the footing from punching shear consideration is
4. If the width of the bedplate is 3m and the clearance is 0.3 what is the upper width of the machine foundation
A footing of size 2.5 m x 2.5 m and 500 mm thick resists characteristic axial loads of 800kN dead and 300 kN imposed from a 400 mm square column. The safe bearing pressure on the soil is 230 kN/m2 and the characteristic material strengths are fcu = 35 N/mm2, fy=460N/mm2. Density of concrete is 24 k N/m3. Cover to all reinforcement is 50 mm. Determine the design load b) Check whether the base pressure is safe c) Design the bending reinforcement, assuming 16 mm diameter bars.
A rectangular footing 23 m x 32 m x 0.34 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 341 kN LL = 216 kN fc = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab Write your final answer with 2 decimal places if the unit is MPA
QUESTION 3 A footing of size 2.5 m x 2.5 m and 450 mm thick resists characteristics axial loads of 500KN dead and 200 kN imposed from a 300mm square column. The safe bearing pressure on the soil is 230kN/m?. a. Check whether the base pressure is safe b. Design the bending reinforcement, assuming 16mm diameter bars c. Check the punching shear Further Design Information Characteristic strength of concrete (fm) = 35 N/mm? %3D Characteristic yield stress of steel (f;) 460 N/mm2 Cover to reinforcement = 75 mm Diameter of main bars = 16 mm Unit weight of concrete = 24 kN/m³