1. A 100mm x 200mm timber beam has a span of 4.0m and carries a uniform load of 15kN/m. including its own weight. For wood E=14000Mpa Fb allow=11Mpa For Steel E-200000Mpa Fb allow=120Mpa Thickness 10mm Width of steel plate based on the allowable bending of steel 95.47mm O 101.47mm 98.47mm O 103.47mm W L

1. A 100mm x 200mm timber beam has a span of 4.0m and carries a uniform load of 15kN/m. including its own weight. For wood E=14000Mpa Fb allow=11Mpa For Steel E-200000Mpa Fb allow=120Mpa Thickness 10mm Width of steel plate based on the allowable bending of steel 95.47mm O 101.47mm 98.47mm O 103.47mm W L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Quiz/ find the angle of rotation of the free end for the beam shown, then find the max sheaving stress If you know GAI = 28 GN/m² Gst=83 GN1m² GBV = 35 GN/m² Aluminum steel Bronzer Do d=100mm 3m d=75mm 2m 1.5m 1.5 KN.m
Part 2 A Pratt roof truss is loaded as shown. Using the method of joints and the method of sections, determine the force in all members. the force P.325KN 80 kN P kN 60 kN D H 8 m 60 kN A G---Y. MATHaling.com 6 m 6 m E 6 m 40 kN 100 kN 6 m
04. Analyze completely the compound truss loaded as shwon below. D 24 kN 3 m E 2 m F 3 @ 4 m 12 PROBLEM 4 TABLE OF ANSWERS: МЕМBER NUMBER FORCE (k) AB 1 CD 2 EF 3 BC CF 5 BF 6 DE 7 AD 8 AE 9 4.
Determine the force in member ( EB )of the roof truss shown in fig 3000 loo0 N lo00N f. wode 30 oa bsw m A 2 m 2m 2m 2m Obuing
Part 2 A Pratt roof truss is loaded as shown. Using the method of joints and the method of sections, determine the force in all members. the force P.171kN 80 kN P kN 60 kN H 8 m 60 kN A G- MATHalino.com 6 m C 6 m E 6 m 40 kN 100 kN 6 m
3. The roof truss is subjected to the loadings shown. Determine the force in each member and indicate if the members are in tension or compression. Approximate each joint as a pin. 200 N C 300 N 300 N 1.5 m B, D. 4 m 3 т H 3т G F 3 m 3 т o00 00 00 o oo 150 N Paint X ite
Determine the safe uniform load that the sectioncould carry if length of the beam is 7m. 76.53 kN/m ➤ Determine the shear flow at the neutral axis. 942.4 N/mm > Determine the shear flow of the portion of the flange 20mm from the edge. 85.7/1N m
10.33 ull LTE K KUDA LIAR E LEMBAR KERJA 4 3 Determine the force in each member of the truss shown. State er each member is in tension or compression. 3 of 3 10 kips B 7.5 ft H G E -6 ft--6 ft-6 ft→-6 ft→| www.statikastruktur.wordpress.com Page 2 4 A floor truss is loaded as shown. Determine the force in members CF, EF, and EG. 250 lb 500 lb 500 lb 375 lb 250 lb 250 lb 125 lb 4 ft 4 ft 4 ft 4 ft 4 ft 4 ft D Bo G H E 2 ft Ao C 5 A valuted roof truss is loaded as shown. Determine the force in members BD, BE, and CE. +2 m 2 m→2 m 2 m-2 m 2 m→ |240 N 360 N F 360 N 240 N 240 N 120 N D 120 N 1.75 m В K L 0.4 m C E 3 m 6 For the frame and loading shown, determine the force acting on member ABC (a) at В, (Ь) at C. 8 in. 10 in. 80 lb 8 in. A 6 in. 6 in. B 10 in.
Determine the maximum safe service live load that the beam can carry if the service dead load is 10kN/m including the beam weight and based on the capacity of the beam section shown. Use fc'=40MPA and fy=415MPa. top bars are 6-36mm and bottom bars are 3-36mm, center to center distance between the top bar layers is 108mm. WLL = kN/m 70 mm 108 mm 352 mm 70 mm 300 mm 7.2m 6.7m A В O O
Determine the maximum safe service live load that the beam can carry if the service dead load is 12 kN/m including the beam weight and based on the capacity of the beam section shown. Use fc'=40 MPa and fy=415 MPa. Top bars are 6-32mm and bottom bars are 3-28 mm, center to center distance between the bar layers is 108mm. 7o mm 108 352 7o mm 300 mm
SITUATION 1 Determine (approximately) the force in each member of the truss. Assume the diagonals can support either a tensile or a compressive force and assuming that the diagonals cannot support a compressive force. A. Use Method 2 7 k 14 k 14 k 7 k H F E 2k 6 ft D В 8 ft 8 ft 8 ft B. Use Method 1 50 kN 40 kN 20 kN | F E 3 m |B 3 m 3 m
20 k G 01. Determine the force in each member of 15 ft F 10k the truss shown below. Indicate if the 10 k E members are in tension or compression. Assume all members are pin connected. 10 ft 20 k 20 k 25 ft 15 10 25 25 15 ft PROBLEM 1 TABLE OF FORCES: МЕМBER NUMBER FORCE (k) AE 1 EG GF 3 BF AC 5 CD BD СЕ 8 CG DG 10 DF 11 67